Ph: 1300 363_ 352
Fax: (02) 8323_ 4000
Pop Rivets - Large Head

4mm pop rivets for the Alubind project and the Photon Factor project. Box of 1000.

Use these rivets to join the D-Clip to the back piece of the Alubind. The larger head holds onto the tricky polyproplylene in the Photon Factor project.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
ABLR
$95.00
D-Clip

Attaches to the inside back of the Alubind to hold the paper in place

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
ABDC
$0.75
Piano Hinge

Purchase these pre-cut hinges specifically for the Alubind project.

They are cut shorter than the length of the aluminium front and back pieces so that there is some room for error.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
ABPHC
$2.90
Piano Hinge - 25m Roll

Purchase this in a bulk roll and then cut to any size you need.

This is a nickel plated steel hinge with 4mm holes.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
ABPHR
$185.00
Nails - Pack of 1000

This nail pack is designed to suit the Briefhaus project.

One packet will cover approximately 4 classes. These are small nails so they don't need any pilot holes and they won't bend. Touch up paint is recommended on the head of the nail.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
BHN
$16.00
Pop Rivets - Small Head

4mm pop rivets for general use.

Specifically for the Alubind project and the Photon Factor project. Ideally drill a 4.1mm hole for these rivets adn remember to de-burr any holes drilled into aluminium.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
ABRS
$90.00
Washers - Box of 200

Washers for 4mm Pop Rivets - Box of 200.

These are used on the non stem end of pop rivets to give them greater surface area when riveting thin sheet material like polypropylene. Put the rivet through the material to be joined, put the washer over the rivet, and then snap the rivet with pop rivet pliers.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
PFRW
$5.00
Nylon Snap Rivets

These handy snap rivets are a good fastener.

A great solution to joining the polypropylene in the Photon Factor project. No extra equipment required, these can be put on by hand.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
PFSR
$40.00
Screws

Pack of 100 screws.

These are the best screws for the Ecolamp project. They are self tapping and won't rust. 2 per student. Use a cordless drill in the classroom and help your students become unfazed by removing screws easily.

How to order:

Fax your order to (02) 83234000
Or email your order to admin@designability.com.au
We will send the goods out with an invoice.
To make card payments please call 1300 363 352 

Code
EL00615026
$7.50
© Copyright by Designability 2012 ABN: 35094314708